PRODUCTS

  • Tungsten Carbide an overview ScienceDirect Topics

    Doping of tungsten carbide with cobalt further improves toughness and strength in such materials. NP-sized particles of tungsten carbide and tungsten carbide cobalt can penetrate cultured mammalian cells. In a study carried out on human and animal cultured cells it was found that NPs of tungsten carbide alone were not acutely toxic to these cells.

    A Study of Tungsten Carbide Surfaces during the Electrical

    Tungsten carbide contains very small cobalt particles, 1–10 µm in size, that are used as binders [9]. Microcracks appear on the surface of the tungsten carbide workpiece when they are machined with EDM. Because of their lower melting point, the cobalt particles melt and separate from the tungsten carbide. When using these workpieces as molds or tools, an important problem is their short product shelf life. Singh et al. [10] studied

    Grinding Tungsten Carbide Used for Manufacturing Gun Drills

    The research focused on DK460UF tungsten carbide that consists of 91 % WC and 9 % Co. It is the main material used in twist drills, gun drills, end mills, etc. The aim of this study was to determine the optimum manufacturing parameters that lead to the desired surface quality. 1 STATE OF THE ART Given its importance, the grinding process has been

    Dislocation networks in tungsten carbide studied by the

    Dislocation networks in tungsten carbide (WC) have been studied in the HVEM. The nodes of the network have been resolved by using the weak‐beam technique in the high voltage electron microscope. They consist of parallel partial dislocations, which are concluded to have Burgers vectors of

    (PDF) Tungsten carbides and W-C phase diagram Aleksey

    The temperature of the Atomic Defects in Hexagonal Tungsten Carbide Studied eutectoid decomposition γ-WC1 x ⇔ δ-WC + C by Positron Annihilation, Phys. Rev. B: Condens. Matter, (2993 K) was inferred from the DTA data reported by 2000, vol. 61, no. 9, pp. 5945–5948. Rudy and Hoffman for a carbide sample containing 10.

    A Study of Tungsten Carbide Surfaces during the Electrical

    machining of tungsten carbide. Tungsten carbide is a type of cemented carbide made by powder metallurgy process, in which the particles of carbide are bound with other metals, such as in tungsten carbide (WC-Co) or titanium carbide (TaC). Tungsten carbide

    Investigation of the Effect of Tungsten Carbide (WC

    Studies of a powder used as a modifier obtained from solid-alloy waste, such as tungsten carbide (drill balls), are presented. Dispersion, particle morphology and phase analysis of the powder were studied. The powder obtained from solid-alloy waste is a phase it is tungsten carbide WC, it consists of nanoobjects of various shapes (nanoparticles, nanoplastics) up to 100 nm in size, with a

    (PDF) Tungsten carbides and W-C phase diagram Aleksey

    The crystal structures of the tungsten monocarbide δ-WC and the disordered lower carbide β-W2C are studied. Using magnetic susceptibility measurements, the hexagonal carbide δ-WC is shown to be stable from 300 to 1200 K. The sequence of phase

    Dislocation networks in tungsten carbide studied by the

    OSTI.GOV Journal Article: Dislocation networks in tungsten carbide studied by the weak-beam technique

    Metallographic Studies of Iron Carbide and Tungsten

    We have just completed an etching study of iron carbides made in three different ways and of some tungsten carbide (1/32-in. equilateral triangles) single crystals. The iron carbide studies, made

    Tungsten carbides and W-C phase diagram SpringerLink

    The crystal structures of the tungsten monocarbide δ-WC and the disordered lower carbide β-W2C are studied. Using magnetic susceptibility measurements, the hexagonal carbide δ-WC is shown to be stable from 300 to 1200 K. The sequence of phase transformations associated with β-W2C ordering is analyzed. The temperature and composition stability limits of the cubic carbide γ-WC1−x are

    Mechanical properties and fracture characteristics of

    Nanoindentation was used to investigate mechanical properties and fracture characteristics of cemented tungsten carbide with fine microstructure. The elastic modulus and hardness of tungsten carbide grains were found to be significantly greater than those measured in cobalt binder rich regions, respectively. From the indented surfaces, very few evidences of cracking or fragmentation were

    Mechanical properties of tungsten carbide-11 cobalt (WC

    Internal friction measurements were performed in different grades of tungsten carbide-cobalt (WC-Co) cemented carbides from room temperature to 1300 K. The results show that WC-Co exhibits an internal friction spectrum composed mainly of a relaxation peak and a high-temperature exponential background. It is shown that these two components are caused by damping mechanisms that take place in the

    Grinding Tungsten Carbide Used for Manufacturing Gun Drills

    determine surface roughness for the tungsten carbide gun drills (less frequently studied) in terms of different cutting conditions, using different grinding wheel grit and taking into account the grinding wheel wear. There is a special case of sharpening small diameter deep hole drilling tools. In this case,

    Structural and Electrochemical Studies of Pt Clusters

    High-surface-area tungsten carbide (WC) was synthesized via a molten solvent route and investigated as a noncarbon electrocatalyst support for nanosized Pt clusters. Pt clusters less than ∼3 nm in size with a small particle size distribution were homogeneously deposited on the WC support by galvanic displacement with Cu. The activity of supported Pt clusters for the oxygen reduction reaction

    Investigation of the Effect of Tungsten Carbide (WC

    Studies of a powder used as a modifier obtained from solid-alloy waste, such as tungsten carbide (drill balls), are presented. Dispersion, particle morphology and phase analysis of the powder were studied. The powder obtained from solid-alloy waste is a phase it is tungsten carbide WC, it consists of nanoobjects of various shapes (nanoparticles, nanoplastics) up to 100 nm in size, with a

    Dislocation networks in tungsten carbide studied by the

    OSTI.GOV Journal Article: Dislocation networks in tungsten carbide studied by the weak-beam technique

    Catalytic properties of tungsten carbide powders in

    Reused tungsten carbide powder retains catalytic activity during three cycles of usage. The individual composition of the gasoline fractions of cracking products in the presence of tungsten carbide powders was studied. AB The relevance of the research is related to the need to develop effective methods of processing heavy hydrocarbon feedstocks.

    Oxidation of tungsten carbide powders in air

    01-11-2013· The behavior of hexagonal tungsten monocarbide powders with the average particle size from 20 to 6000 nm in air in the temperature interval 323–1173 K is studied by differential thermal and thermogravimetric analyses, X-ray and laser diffraction methods and scanning electron microscopy.It is established that WC powders are oxidized, irrespective of their dispersity, to higher oxide WO 3.

    (PDF) Mechanical properties and fracture characteristics

    Mechanical properties and fracture characteristics of cemented tungsten carbide with fine microstructure studied by nanoindentation International Journal of Surface Science and Engineering, 2008 Yi Xiong

    Mechanical properties of tungsten carbide-11 cobalt (WC

    Internal friction measurements were performed in different grades of tungsten carbide-cobalt (WC-Co) cemented carbides from room temperature to 1300 K. The results show that WC-Co exhibits an internal friction spectrum composed mainly of a relaxation peak and a high-temperature exponential background. It is shown that these two components are caused by damping mechanisms that take place in the

    Grinding Tungsten Carbide Used for Manufacturing Gun Drills

    determine surface roughness for the tungsten carbide gun drills (less frequently studied) in terms of different cutting conditions, using different grinding wheel grit and taking into account the grinding wheel wear. There is a special case of sharpening small diameter deep hole drilling tools. In this case,

    Atomic defects in hexagonal tungsten carbide studied by

    Vacancies on the two sublattices of hexagonal tungsten carbide were identified by means of positron lifetime studies after irradiation with electron of various energies. In the as-prepared state two predominant positron lifetime components occur indicating positron annihilation in the free state with a lifetime τ f =124+/-10 ps according to the simple trapping model and positron trapping and

    Structural and Electrochemical Studies of Pt Clusters

    High-surface-area tungsten carbide (WC) was synthesized via a molten solvent route and investigated as a noncarbon electrocatalyst support for nanosized Pt clusters. Pt clusters less than ∼3 nm in size with a small particle size distribution were homogeneously deposited on the WC support by galvanic displacement with Cu. The activity of supported Pt clusters for the oxygen reduction reaction

    Ontdek het metaal wolfraam/tungsten Metel

    Wolfraam/tungsten wordt veel gebruikt in de medische industrie vanwege zijn hoge dichtheid van 19,25 g/cm³. Het feit dat wolfraam een niet-giftig metaal is, maakt het ideaal voor ziekenhuizen en medische instellingen. Het brengt de gezondheid van de patiënten niet in gevaar en het beschermt hen tegen schadelijke radioactieve straling.

    Physical and chemical studies of tungsten carbide

    Typically, the tungsten oxide is heated up to 650–950 °C under a controlled flow of the carburizing agent with low heating rates (ca. 1–10 °C min −1). 22–30 Tungsten carbide formation proceeds via several steps from WO 3 → W x O y → WO 2 → W → W 2 C → WC, where W x O y represents a sub-stoichiometric tungsten

    Investigation of the Effect of Tungsten Carbide (WC

    Studies of a powder used as a modifier obtained from solid-alloy waste, such as tungsten carbide (drill balls), are presented. Dispersion, particle morphology and phase analysis of the powder were studied. The powder obtained from solid-alloy waste is a phase it is tungsten carbide WC, it consists of nanoobjects of various shapes (nanoparticles, nanoplastics) up to 100 nm in size, with a

    Research Progress of Tungsten Carbide Cemented Carbide

    02-08-2019· The tungsten carbide powder produced by this method is micron-sized and can not be further refined. In recent years, the preparation technology of tungsten carbide powder has been fully studied and developed, and many nano-sized powder preparation technologies have been applied, such as direct reduction carbonization, plasma, mechanical alloying, gas phase carbonization, etc.

    Mechanical properties of tungsten carbide-11 cobalt (WC

    Internal friction measurements were performed in different grades of tungsten carbide-cobalt (WC-Co) cemented carbides from room temperature to 1300 K. The results show that WC-Co exhibits an internal friction spectrum composed mainly of a relaxation peak and a high-temperature exponential background. It is shown that these two components are caused by damping mechanisms that take place in the

    (PDF) Mechanical properties and fracture characteristics

    Mechanical properties and fracture characteristics of cemented tungsten carbide with fine microstructure studied by nanoindentation International Journal of Surface Science and Engineering, 2008 Yi Xiong

    Wear mechanisms of coated tungsten carbide when machining

    tungsten carbide could deliver performance using cutting Inconel 718 with economic improvement. Currently, the application of coated tungsten carbide when machine Inconel 718 in cryogenic condition has been studied by researchers such as Badroush et

    Atomic defects in hexagonal tungsten carbide studied by

    Vacancies on the two sublattices of hexagonal tungsten carbide were identified by means of positron lifetime studies after irradiation with electron of various energies. In the as-prepared state two predominant positron lifetime components occur indicating positron annihilation in the free state with a lifetime τ f =124+/-10 ps according to the simple trapping model and positron trapping and

    Kinetics of chemical vapor deposition of tungsten

    30-10-1992· Hard tungsten carbide based coatings were deposited by chemical vapor deposition (CVD) at low temperatures onto metal substrates by hydrogen reduction of tungsten hexafluoride (WF 6) in the presence of dimethyl ether (DME).These coatings contain a mixture of tungsten and tungsten carbide in the form of W 3 C, W 2 C, or a combination of W 3 C and W 2 C depending on reaction

    Does Tungsten Rust? Techiescientist

    27-05-2021· No. For jewelry grades, tungsten is mixed with nickel-binder to make it more suitable to chisel. A binder helps with binding carbide and Tungsten together which oxidizes above 600°C. No human will ever encounter the ring at such an extreme temperature. The tungsten gets affected by acidic conditions having pH 1 and 0.

    Ontdek het metaal wolfraam/tungsten Metel

    Wolfraam/tungsten wordt veel gebruikt in de medische industrie vanwege zijn hoge dichtheid van 19,25 g/cm³. Het feit dat wolfraam een niet-giftig metaal is, maakt het ideaal voor ziekenhuizen en medische instellingen. Het brengt de gezondheid van de patiënten niet in gevaar en het beschermt hen tegen schadelijke radioactieve straling.